Copying a disc with ImgBurn is a two step job, and knowing that up front saves you a lot of confusion. ImgBurn does not copy straight from one disc to another in a single pass. Instead, you read the disc into an image file on your computer first, then you write that image file to a blank disc. That spare image is handy, because you can burn the same disc again later without reading the original a second time. ImgBurn is freeware by LIGHTNING UK!, and the latest and final version is 2.5.8.0, released 16 June 2013. It has had no updates since, and it has no official Windows 11 support, but users report it still works on Windows 10 and 11.
What Copying a Disc Really Means in ImgBurn
When you copy a disc in ImgBurn, you are making an image of the original, then writing that image to a blank disc. The first step is Read mode, which creates an image file from a disc. The second step is Write mode, which writes an image file to a disc. You need both steps, and you need them in that order. There is no single button that reads and writes at the same time, and there is no need for two drives. One drive is enough, because you read the original, swap it for a blank disc, and then write the image. You also need enough free hard drive space for the image file, about 4.7 GB for a full DVD.
There is one hard limit you must understand before you copy anything. ImgBurn is based on the DVD Decrypter burning engine, but it cannot bypass CSS or any copy protection. If a disc is protected, ImgBurn will not strip that protection for you, and it cannot copy a protected disc as a playable copy. That is not a setting you can change, and it is not a fault in your drive. ImgBurn also has no USB burning, no drag and drop, no DVD menu creation, and no transcoding, so a copy job is a straight read and write of the disc as it stands. If the disc is yours and it is not protected, such as a data disc you burned yourself, ImgBurn can copy it cleanly.
- A Windows computer with a working disc drive
- Enough free hard drive space for the full image file
- A clean copy of ImgBurn, version 2.5.8.0
- One blank disc of the same type as the original
- The original disc, clean and free of deep scratches
Step 1: Read the Original Disc to an Image File
Insert the original disc into your drive and open ImgBurn. Click Read on the main screen. Read mode creates an image file from a disc, and it is the first half of any copy job. In the source box, ImgBurn should show your drive and the disc inside it. If it shows no disc at all, check that the disc is seated properly, close other programs that might be using the drive, and try again. In the destination box, pick a folder on your hard drive with enough free space, and give the image a clear file name. ImgBurn supports CD, DVD, HD DVD, and Blu-ray discs. A slower read speed can help with an older or scratched disc. Click the big Read button and let ImgBurn read the whole disc. Do not open the drive tray, and do not shut the computer down while the read is running. When Read mode finishes, check that the image file is in the folder you chose.
Step 2: Write the Image to a Blank Disc
Once you have the image file, the copy is half done. Eject the original disc and insert a blank disc of the same type. If you copied a DVD, use a blank DVD. If you copied a CD, use a blank CD. Match the blank disc to the original. Go back to the main screen in ImgBurn and click Write. Write mode writes an image file to a disc, and it is the second half of the copy job. Click the folder icon next to the source box and pick the image file you just created in Read mode. Check that the destination shows your burner drive, and check the size of the image against the capacity printed on the blank disc. Set your write speed before you click the big Write button. A moderate speed is a good choice, and a slower speed is better if the media is cheap or the drive is old. Turn on Verify to check the finished disc against the image. Click the big Write button and wait.
Copying Different Types of Discs
Not every disc copies in quite the same way, so it helps to know what to expect. A data CD or data DVD is the easiest copy, because it is just files on a disc, and Read mode followed by Write mode handles it cleanly. An audio CD copies as an audio CD when you read it to an image and write that image back, and you should use a slow to moderate write speed so the copy plays well on older players. What matters most is matching the blank disc to the original. A CD copy needs a blank CD-R for a write once copy, or a CD-RW if you want a rewritable disc. A standard CD holds 700 MB or 80 minutes of audio, and a standard single layer DVD holds about 4.7 GB.
Check the Copy Before You Put the Original Away
When the write finishes and verification passes, do not put the original disc away just yet. Test the copy first. If it is a data disc, open it in File Explorer and check that your files are there and that a few files open. If it is an audio CD, play it in your computer and, if you can, in a normal CD player, and listen to the start of a few tracks. If it is a DVD Video disc, play it in your computer and in a DVD player if you have one. Verification already compares the copy with the image, but a quick play test tells you the disc works in the real world. If the copy plays and reads cleanly, keep the image file on your hard drive as a backup, so you can burn another copy later without needing the original disc again. If the copy does not work, the image file still helps. If the read step failed, the problem is the original disc or the drive. If the write failed, the problem is the blank media, the speed, or the burner drive.
When Copying Fails, and What ImgBurn Cannot Copy
A failed copy usually has a simple cause, and the ImgBurn log will usually name it. Open View, then ImgBurn Log, and look for the exact error. An I/O Error points to a read or write problem, and a Power Calibration Area Error usually means the media or the drive is at fault. Bad or cheap media is the most common cause, followed by a dying drive, a write speed that was too fast, a dirty lens, and the wrong mode. Try a different blank disc first, then a slower speed, then a different drive if you have one. Check the original disc for scratches, and clean it gently with a soft cloth if it is dirty. There are also jobs ImgBurn simply cannot do. ImgBurn cannot bypass CSS or any copy protection, so it cannot copy a protected commercial disc as a playable copy. It cannot burn to a USB drive, it has no drag and drop, it cannot create DVD menus, and it cannot transcode video. It has had no updates or security fixes since 2013, so it cannot fix a worn out drive.
Conclusion
Copying a disc with ImgBurn is a two step job: Read mode turns the original into an image file, and Write mode turns that image into a copy on a blank disc. Match the blank disc to the original, use a moderate write speed, turn on verification, and test the copy before you put the original away. ImgBurn cannot bypass copy protection, and it has had no updates since 2013, but for discs you own and made yourself, it is still a small, free, and accurate tool for making a clean copy. Use a clean copy of ImgBurn, use good blank media, and read the log if a step fails.
Read next: How to Burn an ISO File with ImgBurn
Read next: How to Burn a DVD with ImgBurn
Read next: ImgBurn Not Working on Windows 10 or 11? Fixes That Work
